Waves Q-Clone EQ Sampling System Waves Q-Clone Manual 1
LOAD will replace any existing sampled EQ with the one in the preset. ADD will load the preset on top of the current EQ settings. Since the Q-C
CALIBRATING: In this section we will learn how to calibrate the Q-Clone with our Hardware EQ in order to achieve the best cloning results. First,
If the set up is not working properly, you will see the word “Waiting” in one or both parts of the GUI. This can happen when the physical loop betw
Quick Start up and Set up: Here are basic, step by step directions on how to prepare your session to use the Q-Clone and clone your EQ device for
8. Open the Q-Capture on this AUX track and make sure that this is the only plug-in that you have on this track’s plug-in list. 9. Calibrate the Q-
C. Reset – Reset the preset by loading the “reset preset” file from the Load menu. D. Add on top – By clicking the “Add” button you can load a new
7. Set the I/O of this track to match the insert I/O that you used in steps 1 & 2. The basic I/O setting can be done from the Nuendo/Cubase
Waves Q-Clone Manual 17
8. Put the Q-Capture in the first Nuendo/Cubase Insert slot. It will be located in the Waves Plug-In list. Waves Q-Clone Manual 18
9. Arm the monitor (push the monitor button) on this track 10. Calibrate your EQ hardware with the Q-Capture following the directions on the Cali
Introduction You own a great sounding hardware EQ. It sounds great. It feels good. You know just how to “tweak” the knobs to get the sound that yo
13. When the Q-Clone is opened it will be in “Hold” mode. When you switch the “Capture” on, it will be able to start receiving the cloning image f
D. Add – By clicking the “Add” button you can load a new preset on top of an existing one. The “Add” mode gives the effect of having 2 or more EQ d
7. Arm the “Record” button and the “Input Echo” button. (Click them on.) 8. Calibrate the Q-Capture with your EQ device as instructed in the
New File”. This saves a preset file to any desired directory on your computer. B. Save your EQ to your Waves Preset Menu - Click the “Save” button
6. Open your Logic session and open a new Audio file (which will be dedicated to the Q-Capture). 7. On this track, assign the input of the channe
10. Calibrate the Q-Capture with your EQ device as instructed in the Calibration chapter on page 11. 11. On an Audio track (the one that you want to
D. Add – By clicking the “Add” button you can load a new preset on top of an existing one. The “Add” mode gives the effect of having 2 or more EQ d
B. “Setup” menu, choose “Configure Audio System” and choose the “Input Monitoring Mode…” Waves Q-Clone Manual 27
In this dialog box check the “Always” option and click OK. 6. Open your DP session and open a new Audio file (which will be dedicated to the Q-C
11. Calibrate the Q-Capture with your EQ device as instructed in the Calibration section on page 11. 12. On an Audio track (the one that you want
BEHIND THE SCENES The Q-Capture component sends a continuous test signal (routed to the audio card output) to the input of the EQ-device that is
Waves Q-Clone Manual 30 c. Reset – Reset the preset by loading the reset preset file from the Load menu. d. Add – By clicking the “Add” button y
Waves Q-Clone Manual 31maximum capacity, the real time tasks have dropouts which result in flashing “No Transmission” messages. 7. Sonar will have
Waves Q-Clone Manual 32 Q-CLONE TROUBLESHOOTING CHECK LIST: Problem Synopsis Action I’m capturing a flat device setting but the curve in
Waves Q-Clone Manual 33Q-Clone shows “No Transmission” on the frequency response display. - Q-Capture is not well routed, is in bypass or disabled.
Waves Q-Clone Manual 34
Once the test-signal returns from the device, it is analyzed and loaded into the Q-Clone component as an impulse-response. This happens several time
Q-Capture Component The Q-capture sends a test signal from its output that is intended to be fed back into its own input through the EQ-device. It
The Receiving section also shows an input meter to indicate the signal level returning from your EQ device, back into the channel. CALIBRATION
Q-Clone Component The Q-Clone plug-in has 2 main controls - Gain and Mode. It also has a Scale control for the frequency response graph. The Mod
Clone, except that the overall EQ will be shown in a single graph and the CPU usage will be that of only a single instance. Please note that to swi
When a Q-Clone instance is launched it will load in Hold mode with a flat EQ response. When you switch to the Capture or Add modes it will check for
Comments to this Manuals